Tapetech CFFULL Cont. Flow Full Bundle Manuel d'utilisateur

OperationDrywall Feed PumpU.S. Patents Pending: 61/315,288; 61/315/322; 61/316,013; 61/316,010- For water-based materials only - - Not for use in expl

Prime Pump 10 3A0245APrime Pump1. Mix material in separate bucket.2. Add 1-2 gallons (4-8 liters) of material to hopper.3. Place prime hose deflector

Using Finishing Tools3A0245A 11Using Finishing ToolsCorner Finishing1. Attach corner finisher inlet swivel to inline valve controller (JJ) valve using

Using Finishing Tools 12 3A0245AFlat Box Finishing 1. Attach male inlet of box finisher to the Z-swivel assembly using quick-connect clamp attached to

Using Finishing Tools3A0245A 13Automatic Taping1. Remove creaser wheel trigger pin.2. Attach taper tool to inline valve.3. Position creaser wheel trig

Storage 14 3A0245AStorage1. Perform Pressure Relief Procedure, page 6 (prime valve handle in down position). Leave prime valve handle in PRESSURE RELI

Troubleshooting3A0245A 15TroubleshootingMotor Will Not Operate (See flow chart, page 25)PROBLEM CAUSE SOLUTIONBasic fluid flow problems Flow control k

Troubleshooting 16 3A0245ALow or Fluctuating OutputPROBLEM CAUSE SOLUTIONLow output Pump is worn or clogged. Service pump. Check piston and intake val

Troubleshooting3A0245A 17Low or Fluctuating Output (continued)Electrical ShortPROBLEM CAUSE SOLUTIONMotor runs and pump strokes No material supply. Re

Troubleshooting 18 3A0245ARF ProblemsPROBLEM CAUSE SOLUTIONUnwanted signal will not allow unit to learn the controller.Unwanted RF signal. Undesired c

Troubleshooting3A0245A 19Electrical ProblemsSymptom: Unit does not run or stops running.Perform Pressure Relief Procedure; page 6.• Plug unit into cor

Warning 2 3A0245AWarningThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point sym

Troubleshooting 20 3A0245ADrywall feed pump does not run at allCheck transducer or transducer connections (control board is not detecting a pressure s

Troubleshooting3A0245A 21Drywall feed pump does not run at allControl is commanding motor to run but motor shaft does not rotate. Possibly locked roto

Troubleshooting 22 3A0245ADrywall feed pump does not run at allControl is commanding motor to run but motor shaft does not rotate. Possibly locked rot

Troubleshooting3A0245A 23Drywall feed pump does not run at allIs motor overheating? NOTE: Motor must be cooled down for the test.1. Allow unit to cool

Troubleshooting 24 3A0245AUnit Will Not Shut OffPerform Pressure Relief Procedure; page 6. Leave prime valve handle open and power switch OFF.Troubles

Troubleshooting3A0245A 25Unit Will Not Run(See following page for steps)Turn unit ON.Error Code DisplayedSee Error Code section for further troublesho

Troubleshooting 26 3A0245AUnit Will Not Run - Steps: 100-120 VAC NA UnitsDigital DisplayControlBoardThermal SwitchMotor LeadsPotentiometer20A/15A Swit

Troubleshooting3A0245A 27Unit Will Not Run - Steps: 100-120 VAC UK Digital DisplayControlBoardThermal SwitchMotor LeadsPotentiometerPressure Transduce

Troubleshooting 28 3A0245AUnit Will Not Run - Steps: 220-240 VAC UnitsDigital DisplayControlBoardThermal SwitchMotor LeadsPotentiometerPressure Transd

Technical Data (Unit)3A0245A 29Technical Data (Unit)Technical Data (Pump)Power requirements:Models 257100, 262288Models 258906, 262300Model 258907100-

Warning3A0245A 3MOVING PARTS HAZARDMoving parts can pinch, cut or amputate fingers and other body parts.• Keep clear of moving parts.• Do not operate

Notes 30 3A0245ANotes

Graco Standard Warranty3A0245A 31Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and b

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves th

Component Identification (Unit) 4 3A0245AComponent Identification (Unit)APump ModuleBPrime/Tool Fill/Recirculation Valve/Pressure ReliefCFlow Control

Component Identification (Hoses and Tools)3A0245A 5Component Identification (Hoses and Tools)AAFluid ManifoldBBFluid OutletCCFluid Inlet DDHose 1/2 in

Grounding 6 3A0245AGroundingFCC Notice (FCC ID: JHICED1)Model Number: DFS150This device complies with Part 15 of the FCC rules. Operation is subject

Setup3A0245A 7Setup1. Turn power switch to OFF and connect power cord.2. Connect material hose (DD) to fluid manifold outlet (BB). NOTE: Up to 150 ft

Setup 8 3A0245ANOTE: JOB scrolls past, then the number of gallons dis-pensed displays.2. Press and hold to reset to zero.Lifetime Gallons1. Short pres

Setup3A0245A 96. Press and hold DTS button to clear error code to zero.7. Short press to move to SOFTWARE REV.8. Short press to display number of GUN